Wavlink AC1200 WiFi Extender Setup

Do you prefer to configure a Wavlink WiFi extender using wifi.wavlink.com? You’re in the right place now. Using a Wavlink AC1200 WiFi Extender Setup, you may quickly boost the wireless extender speed and restore lost wireless network signals. With the help of this extension gadget, you may increase the wireless signal’s coverage throughout your house or place of business. If you’re putting up a wavlink range extender for the first time and are unsure of what to do, read this subject in its entirety. Here are the simple steps for setting up a Wavlink range extender.

Installation of wavlink wifi extender 

  • The wavlink ac1200 extender must be turned on.
  • Keep your home’s LAN router and extender close to one another.
  • Visit ap.setup right now.
  • Afterward, select NEW EXTENDER SETUP.
  • Follow all of the instructions displayed on the screen to proceed.
  • Move your AC1200 to the new location of your choice after it is finished.
  • Now that you have other smart devices, you can connect to the network.

Note:- If you need any help regarding your wavlink wifi extender setup feel free and contact our technician or visit an official website that is ap.setup.

Manual method of Wavlink AC1200 WiFi Extender Setup

  • Connect the power outlet to the extender.
  • Once a power LED on any smart device turns on the range extender¬†
  • Navigate to your smart device’s settings menu and select WiFi.
  • On the connection, click “Wavlink-Extender Setup Ext.”
  • Once you’re connected, launch the web browser on your mobile device.
  • Enter the address exactly as it is set up in the link bar.
  • The new setup page for the range extender will open.
  • Refer to the comprehensive instructions to set up the extender.

WPS method of Wavlink AC1200 WiFi Extender Setup

the following instructions to set up your wavlink ac1200 using WPS:

  • Turn on your Wavlink WiFi extension after unpacking it.
  • Place your ac1200 near your main router.
  • The WPS button on the extender needs to be depressed.
  • After a little interval, press the WPS button on the router.
  • Call our technical team if the router LED doesn’t turn solid green after a minute.
  • Your setup process is complete when the LED turns solid green after flashing.
  • Choose a new location for your Wavlink WiFi extension and set it there.
  • Now, you may connect any WiFi-capable smart device, such a tablet, laptop, desktop, or smartphone.

Steps for troubleshooting the Wavlink AC1200 extender

  • Some IP 192.168.10.1 gateways have a default setting that disables the WPS button. Visit the Wavlink wifi extender setup management website to set up your extender if you are unable to connect using the WPS button.
  • Be sure to position the extender near your wireless router.
  • If not, there will be a noticeable performance difference on your improved network. Keep it at least one metre away from your router.
  • Away from any electrical interference gadgets should be where you are connecting. Using Bluetooth-enabled appliances such as cordless phones, microwaves, and baby monitors is not recommended.

Reset the Wavlink extender setup

Does your Wavlink AC1200 WiFi Extender need to be restarted? The bulk of the time, a factory reset operation is meant to be used when the user is unable to remember the admin password. Your extender will be ready for a new installation when you complete this process. Keep in mind that a factory reset will eliminate all of your customised settings, including your account and password.

In order to reset your wavlink AC1200 WiFi Extender, follow these steps:

  • Plug in and start up your Wavlink AC1200.
  • Hold off until the green light becomes steady and solid.
  • Locate the factory reset hole.
  • It might be reachable from the side of the extension.
  • Grab a sturdy paper clip or pin.
  • In the hole, insert the paper clip or pin, and hold it there for 8 to 10 seconds.
  • Remove the paper clip when the power light is solid green.

 

Leave a Reply

Your email address will not be published.